Ubiquiti: Firmware v5.5.4 disponible
Hace un par de días Ubiquiti ha colocado para la descarga una nueva versión del firmware AirOS v5.5.4.
La larga lista de cambios es:
AirOS V Firmware Revision History ==================================================================== Supported products * Bullet M2/M5/Titanium * Rocket M2/M2 Titanium/M3/M365/M900/M5/M5 GPS/M5 Titanium/M6 * NanoStation M2/M3/M365/M5/M6 * NanoStation Loco M2/M900/M5 * NanoBridge M2/M3/M365/M900/M5 * AirGrid M2/M5/HP/HP New * PowerBridge M3/M365/M5/M10 * PicoStation M2 * AirRouter/HP * PowerAP N ==================================================================== Version 5.5.4-Service Release (March 13, 2013) ---------------------------------------------- New: - New: Data rate module: Alternative data rate algorithm option - New: WEB UI: Audio option for Antenna Alignment Tool - New: WEB UI: "Feed only - 3dBi" option for antenna type (AirGrid and NanoBridge models only) Improvements: - airMax: Improved performance in PtMP scenarios - airMax: Lower latency in Long Range PTP mode - airMax: Voice performance/latency improvements in PtMP scenarios - QoS: Map commonly used VoIP TOS values (0x68, 0xb8) to Voice queue - Speed test: Improved timeout/errors handling and reporting - TFTP recovery: Reset configuration to factory defaults when executing TFTP recovery mode without need to hold Reset button for 15sec and upload firmware image - airView: Update certificate - WEB UI: Show if custom scripts are present on device - WEB UI: Show signal strength from remote radio in Station information window (airMax mode only) - WEB UI: Show Station TX/RX bit rate statistics - WEB UI: Disable WEB UI while airView is running - WEB UI: Automatically redirect to HTTPS port when running Speed test - WEB UI: Make MAC addresses in Main page easily selectable - WEB UI: Add help text for UBNT/Advanced settings pages - WEB UI: Improved FW update failure messages - WEB UI: Do not offer to apply configuration changes if there are no any changes made - WEB UI: Latitude/Longitude setting validation - WEB UI: Interface Language update: French translations - WEB UI: Interface Language update: Lithuanian translation - Stability: Check filesystem on boot - Stability: Memory leak protection for less than 1MB of RAM - Stability: HW watchdog in u-boot Fixes: - Fix: airMax: Radio is transmitting when operating in airView mode (AP mode only) - Fix: airMax: Long range PtP mode: AP gets stuck at 81Mbps rate and transmit throughput goes down - Fix: airMax: Sometimes AP locks up when applying configuration changes (possible fix) - Fix: airSync: Rocket Titanium airSync Slave doesn't connect to airSync Master - Fix: airSelect: Default airSelect announce count set to 30 - Fix: airView: airView does not start when Device Name contains comma symbol - Fix: airView: M900/M3/M365/M6 products does not scan full frequency range - Fix: Detect Ethernet loopback on defective device and bring Ethernet interface down - Fix: Sometimes M Series devices hang during reboot (except Titanium) - Fix: Change Max MTU to 2024 bytes on both Ethernet interfaces - Fix: Returning from Test mode does not revert some configuration changes - Fix: Redirection issue when enabling/disabling HTTPS - Fix: Satellite signal bar is centred under IE - Fix: During upgrade disable default route if DHCP client is configured - Fix: DHCP fallback IP isn't set - Fix: Memory leak in Main page with IE8/IE9 (session timeout implemented) - Fix: Low power mode fix for newer revisions of NanoStation M5 - Fix: Device discovery issue when DMZ port is enabled - Fix: Cannot switch from Advanced to Simple Configuration mode when network role is Router - Fix: Auto Channel does not follow channel plan for Canada (Rocket Titanium) - Fix: OSPF and other unregistered multicast traffic transmit problems in PtMP - Fix: Skip EAP security certificate date validation if device date is before certificate start date - Fix: Do not send discovery/ARP requests through bridge ports - Fix: Enable busybox option to prefer IPv4 - Fix: UPnP: Router should accept "PORT FORWARD" requests from LAN side only - Fix: Sometimes station can't associate when switching from open to WPA security - Fix: Enable DFS when choosing country Austria - Fix: Disable "Block Management" option for WAN in default configuration (AirRouter, AirRouter HP, PowerAP N) Regulatory updates: - Enable DFS for Germany upper band (5.8GHz) channels - Update New Zealand allowed frequencies for 5GHz - Update Chilean allowed frequencies for 5GHz
Puede ser descargado desde la sección download de Ubiquiti
